| Code |
Application |
| G00 |
positioning
(rapid traverse) (M,T) |
| G01 |
linear interpolation
(feed) (M,T) |
| G02 |
circular
Interpolation CW (M,T) |
| G03 |
circular
Interpolation CCW (M,T) |
| G04 |
dwell, a
programmed time delay (M,T) |
| G05 |
unassigned |
| G06 |
parabolic
interpretation (M,T) |
| G07 |
cylindrical
diameter values (T) |
| G08 |
programmed
acceleration (M,T) |
| G09 |
exact stop
check (M,T) |
| G10
- G12 |
unassigned
or lock and unlock devices |
| G13 |
computing
line and circle intersect (M,T) |
| G14
- G14.1 |
used for
scaling (M,T) |
| G15
- G16 |
polar coordinate
programming (M) |
| G15
- G16.1 |
cylindrical
interpolation - c axis (T) |
| G16.2 |
end face
milling - c axis (T) |
| G17 |
XY plane
selection (M,T) |
| G18 |
ZX plane
selection (M,T) |
| G19 |
YZ plane
selection (M,T) |
| G20 |
input in
inch |
| G21 |
input in
mm |
| G22
- G23 |
machine axis
off limit area (M,T) |
| G22.1
- G23.1 |
cutting tool
off limit area (M,T) |
| G24 |
single-pass
rough facing cycle (T) |
| G28 |
return to
reference point (M,T) |
| G29 |
return from
reference point (M,T) |
| G30 |
return to
alternate home position (M,T) |
| G31.1
- G31.4 |
external
skip function (M,T) |
| G33 |
thread cutting,
constant lead (T) |
| G34 |
thread cutting,
increasing lead (T) |
| G35 |
thread cutting,
decreasing lead (T) |
| G36 |
automatic
accel. and deccel. (M,T) |
| G37 |
used for
tool gaging (M,T) |
| G38 |
measure dia.
and center of hole (M) |
| G40 |
cutter compensation
cancel (M) |
| G41 |
cutter compensation
left (M) |
| G42 |
cutter compensation
right (M) |
| G43 |
cutter offset,
inside corner (M,T) |
| G44 |
cutter offset,
outside corner (M,T) |
| G45 |
tool offset
decrease |
| G46 |
tool offset
double increase |
| G47 |
tool
offset double decrease |
| G48 |
scaling off |
| G49 |
tool length
compensation cancel |
| G50 |
tool offset
increase |
| G50.1 |
cancel mirror
image (M,T) |
| G51.1 |
program mirror
image (M,T) |
|
|
| Code |
Application |
| G52 |
offset axis
w/ respect to 0 point (M,T) |
| G53 |
motion in
machine coordinates (M,T) |
| G54 |
work coordinate
system 1 select |
| G55 |
work coordinate
system 2 select |
| G56 |
work coordinate
system 3 select |
| G57 |
work coordinate
system 4 select |
| G58 |
work
coordinate system 5 select |
| G59 |
work coordinate
system 6 select |
| G60 |
single direction
positioning |
| G61 |
exact stop
check mode (M,T) |
| G62 |
reduce feed
rate on inside corner (M,T) |
| G64 |
cutting mode
(M,T) |
| G65 |
custom parametric
macro (M,T) |
| G66 |
custom macro
for motion blocks (M,T) |
| G66.1 |
custom macro
for all blocks (M,T) |
| G67 |
stops custom
macro (M,T) |
| G68 |
coordinate
syslaim rotation ON (M) |
| G69 |
coordinate
syslaim rotation OFF (M) |
| G70 |
inch
programming (M,T) |
| G71 |
metric programming
(M,T) |
| G72 |
circular
interpolation CW (M) |
| G72 |
finished
cut along z-axis (T) |
| G73 |
peck drilling
cycle (T) |
| G74 |
counter tapping
cycle (M) |
| G74 |
rough
facing cycle (T) |
| G74 |
cancel circular
interpolation (M,T) |
| G75 |
circular
interpolation (M,T) |
| G76 |
fine boring |
| G80 |
canned cycle
cancel |
| G81 |
drilling
cycle, no dwell (M,T) |
| G82 |
drilling
cycle, dwell (M,T) |
| G83 |
deep hole,
peck drilling cycle (M,T) |
| G84 |
right hand
tapping cycle (M,T) |
| G84.1 |
left hand
tapping cycle (M,T) |
| G85 |
boring, no
dwell, feed out (M,T) |
| G86 |
boring, spindle
stop, rapid out (M,T) |
| G87 |
boring,
manual retraction (M,T) |
| G88 |
boring, spindle
stop, manual ret. (M,T) |
| G89 |
boring, dwell
and feed out (M,T) |
| G90 |
absolute
dimension input (M,T) |
| G91 |
incremental
dimension input (M,T) |
| G92 |
set absolute
zero point (M,T) |
| G93 |
inverse time
feed rate (M,T) |
| G94 |
per minute
feed (M,T) |
| G95 |
per revolution
feed (M,T) |
| G96 |
constant
surface speed control (T) |
| G97 |
stop constant
surface speed control (T) |
| G98 |
return to
initial point in canned cycle |
| G99 |
return
to R point in canned cycle |
|
|
